Pengaruh Variasi Temperatur Proses Austempering Terhadap Mikrostruktur dan Sifat Mekanik Baja Armour

Slamet Sutjipto; Ilham Azmy; Destri Muliastri; Devi Eka Septiyani Arifin

doi:10.33504/manutech.v15i01.264

Authors

Slamet Sutjipto Politeknik Negeri Bandung
Ilham Azmy Politeknik Negeri Bandung
Destri Muliastri Politeknik Negeri Bandung
Devi Eka Septiyani Arifin Politeknik Negeri Bandung

DOI:

https://doi.org/10.33504/manutech.v15i01.264

Keywords:

armour steel, austempering, microstructure, mechanical properties

Abstract

Armour steel is a medium-carbon steel which is widely used in military and defense industries owing to its ability to protect from projectile and bullet pressure. However, this armour steel still posses mechanical limitation aspect, thus it is needed to engineer for improvement. Therefore, the aim of this research is to undergo mechanical properties engineering by using heat treatment method of austempering within temperature variations of 200, 250, 350, 450, and 500 ^oC . Experimental results show that austempering process affected to fraction quantity of phase and microstructure of ferrite, pearlite, and bainite. Armour steel resulted by austempering process in temperature 500 ^oC depicts microstructure transformation and mechanical properties improvement significantly. Microstructure transformation along with proportional fraction volume phases of upper bainite, ferrite, and pearlite highly beneficial to increase impact strength dan ductility of armour steel. Thereby, armour steel resulted by austempering process in temperature 500 ^oC has thoroughly increased its mechanical properties which capable to be applied in military and defense industries.

Downloads

Download data is not yet available.

References

P. K. Jena, P. Senthil P, and S. K. K, "Effect of tempering time on the ballistic performance of a high strength armour steel," Journal of Applied Research and Technology, vol. 14, no. 1, pp. 47-53, 2016.

Yurianto, Pratikto, S. Rudy, and S. Wahyono, "Optimasi Parameter Quenching Dan Tempering Pada HRP Steel Lokal Sebagai Baja Armor Nasional," Jurnal Rekayasa Mesin, vol. 9, no. 2, pp. 143-148, 2018.

C.-Y. Chen, F.-Y. Hung, T.-S. Lui, and L.-H. Chen, "Microstructures and Mechanical Properties of Austempering SUS440 Steel Thin Plates," Metals, vol. 6, no. 2, 2016.

S. M. Walley, "The Beginnings of the Use of Iron and Steel in Heavy Armour," in Metallurgical Design and Industry, 2018, pp. 71-153.

O. Heidary, O. Mirzaee, A. Honarbakhsh Raouf, and E. Borhani, "Texture development during austempering process of an AISI 4130 steel," Materials Science and Engineering: A, vol. 793, 2020.

B. Bandanadjaja, D. Idamayanti, N. Widarmansyah, and A. Lestarianto, "The effect of first step holding time of low high austempering heat treatment to the mechanical properties of Austempered Ductile Iron (ADI)," IOP Conference Series: Materials Science and Engineering, vol. 541, no. 1, 2019.

A. Ervan, Somawardi, and Sugianto, "Analisis Pengaruh Media Pendingin Dengan Kombinasi Waktu Penahanan Pendingin Terhadap Nilai Kekerasan Baja AISI-1045 Pada Proses Quenching " Manutech: Jurnal Teknologi Manufaktur, vol. 13, no. 01, pp. 25-32, 2021.

H. Rinaldo, M. Januar, and M. M. Sinaga, "Effect of austempering treatment time on strength, ductility, hardness, and abrasive wear resistance of JIS FCD 700 ductile iron," IOP Conference Series: Materials Science and Engineering, vol. 541, no. 1, 2019.

A. H., H. Q., and V. F., "Peningkatan Sifat Mekanik Dan Ketahanan Fatik Pada Baja ASSAB 709 M Melalui Proses Austempering," in Seminar Nasional AVoER XI, Palembang, Indonesia, 2019, pp. 374-379: Fakultas Teknik Universitas Sriwijaya.

Asmadi, A. Reny, N. S. Zahara, and N. Ahmad, "Austempering Dengan Pendingin Oli Pada Baja Strip JIS G4801 SUP 9," TEKNIKA: Jurnal Teknik, vol. 6, no. 1, pp. 47-57, 2019.

M. Badaruddin, B. Bakti, B. Prasetyo, and Sugiyanto, "Effect of austempering temperatures on surface hardness of AISI 4140 steel," IOP Conference Series: Materials Science and Engineering, vol. 1173, no. 1, 2021.