PENGARUH PELUMAS TERHADAP TEGANGAN ALIR DAN GAYA PENARIKAN KAWAT AISI 1006 MENGGUNAKAN METODE FEM

Destri Muliastri; Devi Eka Septyani; Prayoga Lesmana

doi:10.33504/manutech.v13i02.158

Authors

Destri Muliastri Politeknik Negeri Bandung
Devi Eka Septyani
Prayoga Lesmana

DOI:

https://doi.org/10.33504/manutech.v13i02.158

Keywords:

Wire, Wire Drawing, Lubricant, Friction Coefficient, Finite Element Method

Abstract

The wire drawing process is a metal forming technique. The factor affecting the final result of the draw is Lubricants. The value of the friction coefficient will have an impact on the surface quality of the wire, the use of lubricants is needed to reduce the load and surface defects of the wire. The purpose of this study was to determine the effect of lubrication on the flow stress and pulling force of AISI 1006. The lubricants used in this study have different friction coefficient values, including 0.03; 0.02 and 0.01. In this research, the method used Finite Element Method and Ansys workbench 19.0. Finite element method is done by simulating wire drawing with a die angle of 12 degrees. The results obtained will be calculated theoretically and simulated, for lubricants with different coefficient of friction have different values of flow stress and pulling force which can affect mechanical properties. The smaller the friction coefficient, the greater of the average flow stress, the percentage of theoretical calculations and simulations is 2.45%, for the effect of lubrication on the wire pulling force, the percentage is 23.25%.

Downloads

Download data is not yet available.

References

. O. R. Adetunji, D. Ph, S. I. Kuye, D. Ph, M. J. Alao, and B. Eng, “Microstructures of Mild Steel Spring after Heat Treatment . Microstructures of Mild Steel Spring after Heat Treatment .,” vol. 14, no. February, pp. 11–15, 2015.

. W. D. Callister and J. Wiley, Materials science, vol. 79, no. SUPPL. 2002.

. I. M. Sas-Boca, M. Tintelecan, M. Pop, D. A. Ilu?iu-Varvara, and A. M. Mihu, “The Wire Drawing Process Simulation and the Optimization of Geometry Dies,” Procedia Eng., vol. 181, pp. 187–192, 2017, doi: 10.1016/j.proeng.2017.02.368.

. S. Sutjipto, J. T. Mesin, and P. N. Bandung, “BAHAN AJAR MATERIAL – TEKNIK STANDAR- PEMBELAJARAN MINIMAL Disusun oleh,” 2015.

. M. B. Fitrianto, Darmanto, and S. Imam, “Pada specimen halus dalam kondisi dengan pelumas, semakin kental viskositasnya sudut geseknya semakin besar. Pada spesimen kasar dengan kondisi pelumas, semakin tinggi viskositas pelumasnya sudut geseknya semakin kecil,” Gaya gesek, vol. 11, no. 1, pp. 13–18, 2015.

. S. M. Byon, S. J. Lee, D. W. Lee, Y. H. Lee, and Y. Lee, “Effect of coating material and lubricant on forming force and surface defects in wire drawing process,” Trans. Nonferrous Met. Soc. China (English Ed., vol. 21, no. SUPPL. 1, pp. s104–s110, 2011, doi: 10.1016/S1003-6326(11)61071-6.

. M. C. Ruiz, J. Verde, A. Andrés, J. Viguri, and A. Irabien, “Environmental assessment of lubricants before and after wire drawing process,” J. Hazard. Mater., vol. 85, no. 3, pp. 181–191, 2001, doi: 10.1016/S0304-3894(01)00227-8.

. M. T. Hillery and V. J. Mccabe, “precessh g Materials Wire drawing at elevated temperatures using different die materials and lubricants IAVOmeter I Pyrometer l ~ ] k , k . a .. ~ N ,” J. Mater. Process. Technol., vol. 55, pp. 53–57, 1995.

. P. Tornar, R. K. Pandey, and Y. Nath, “Numerical simulation of friction stress in wire drawing produced by direct extrusion process in presence of lubricant starvation,” Procedia Eng., vol. 64, pp. 1320–1328, 2013, doi: 10.1016/j.proeng.2013.09.213.

. P. Kawat and B. Aisi, “TEGANGAN ALIR , REGANGAN DAN GAYA Diajukan Oleh?: Febby Fauziah TERHADAP TEGANGAN ALIR , REGANGAN DAN DENGAN METODE FEM,” 2020.

. M. Firman, M. Darsin, and H. Arbiantara B., “Analisis Kekuatan Tarik Dan Kekasaran Kawat Tembaga Hasil Drawing Akibat Variasi Persentase Reduksi,” Rotor, vol. 6, no. 1, pp. 50-55–55, 2013.

. C. Moon and N. Kim, “Analysis of wire-drawing process with friction and thermal conditions obtained by inverse engineering,” J. Mech. Sci. Technol., vol. 26, no. 9, pp. 2903–2911, 2012, doi: 10.1007/s12206-012-0711-1.