Analisis Pengaruh Parameter Infill Pattern dan Nozzle Temperature terhadap tensile strength Filamen PLA PRO

Zaldy S. Suzen; Riskullah Dirga Trisaplin; Hasdiansah Hasdiansah

doi:10.33504/manutech.v14i01.208

Authors

Zaldy S. Suzen
Riskullah Dirga Trisaplin
Hasdiansah Hasdiansah

DOI:

https://doi.org/10.33504/manutech.v14i01.208

Keywords:

3D printing, PLA PRO, tensile strength, parameter, factorial

Abstract

3D Printing is part of Rapid Prototyping technology, where the printing process converts a 3D design into a solid object, can be held and has volume, the formation is done by placing the filament layer by layer. The purpose of this study was to determine the effect of the process parameters used, to determine the highest and lowest tensile strength values ??and to determine the eligible parameters for car dashboard production. The method in this study using the factorial method multiplied by 15 types of infill and 3 temperature levels so as to create a total of 45 specimens, then replicated 3 times to make 135 samples of specimens, the process parameters used were 15 types of infill and 3 levels of nozzle temperature that were printed in a vertical orientation. The highest tensile strength value is 43.9 MPa with the parameter (infill pattern) 3D honeycomb, nozzle temperature 210?C, and the lowest tensile strength value is 14.7 MPa with the parameter (infill pattern) archimedean chord, nozzle temperature 220?C. The final result of the research shows that there is an influence between parameters on the value of tensile strength and recommends several parameters that can be used to produce car dashboards.

Downloads

Download data is not yet available.

References

. T. H. Saputra, Herianto And H. A. Pamasaria, "Analisa Pengaruh Pemilihan Komponen Terhadap Ketelitian Dimensi Dan Kualitas Permukaan Produk Pada Mesin 3d Printing Jenis Fdm (Fused Deposition Modelling)," In Seminar Nasional Ienaco, Yogyakarta, 2019.

. E. I. Riza, C. Budiyantoro And A. W. Nugroho, "Peningkatan Kekuatan Lentur Produk 3d Printing Material Petg Dengan Optimasi Parameter Proses," Media Mesin: Majalah Teknik Mesin, Vol. 21 No. 2, No. Https://Doi.Org/10.23917/Mesin.V21i2.10856, Pp. 66-75, 2020.

. Y. B. Pratama, Hasdiansah And Pristiansyah, "Pengaruh Parameter Proses Slicing Software Terhadap Kekasaran Permukaan Printing Part Filamen St-Pla," Manutech : Jurnal Teknologi Manufaktur, Vols. Vol. 13, No. 01, No. P-Issn : 2089-5550 , Pp. 34 - 40, 2021.

. Pristiansyah, Hasdiansah And Sugiyarto, "Optimasi Parameter Proses 3d Printing Fdm Terhadap Akurasi Dimensi Menggunakan Filament Efle," Manutech: Jurnal Teknologi Manufaktur, Vol. Vol. 11 No. 01, No. P-Issn : 2089-5550 , Pp. 34-40, 2019.

. A. K. Sood, R. Ohdar And S. Mahaputra, "Improving Dimensional Accuracy Of Fused Deposition Modelling Processed Part Using Grey Taguchi Method," Elsevier Ltd, No. Doi: 10.1016/J.Matdes.2009.0, Pp. 4243-4252, 2009.

. A. Kholil, F. Aufi And E. A. Syaefudin, "Pengaruh Layer Thicness Dan Orientasti 3d Printing Terhadap Material Abs," In National Conference Of Industry, Engineering And Technology, Polines, Semarang, Indonesia, 2020.

. Z. S. Suzen, Hasdiansah And Yuliyanto, "Pengaruh Tipe Infill Dan Temperatur Nozzle Terhadap Kekuatan Tarik Produk 3d Printing Filamen Pla + Esun, 12(02)," Manutech?: Jurnal Teknologi Manufaktur , Vols. Vol.12, No.2 , No. Https://Doi.Org/10.33504/Manutech.V12i2.133, Pp. 73-80, 2020.

. R. Ardiansyah, Z. S. Suzen And Erwansyah, "Pengaruh Parameter Proses Terhadap Kekuatan Tarik Produk 3d Printing Menggunakan Filamen Polylactic Acid (Pla) Buatan R3d Maker," Jurnal Indonesia Sosial Dan Teknologi (Jist), Vols. Vol. 12, No. 12, No. Https://Doi.Org/10.36418/Jist.V2i12.300, Pp. 2153-2164, 2021.

. W. Widiyanto And T. I. Setyani, "Pengaruh Arah Pencetakan 3d Printing Tipe Fdm Bahan Polymer Abs Terhadap Tensile Strength Produk Yang Dihasilkan," Media Mesin: Jurnal Ilmiah Teknik Mesin, Vols. Vol. 21, No.1, No. Https://Doi.Org/10.23917/Mesin.V21i1.9419, Pp. 25-34, 2020.

. Astm D638-14, "Astm International," Standard Practice For Preparation Of Metallographic Specimens, Pp. 82(C), 1–15. Https://Doi.Org/10.1520/D0638-14.1, 2016.

. S. M. Sapuan, N. K. Mun, A. Hambali, H. Y. Lok, A. M. Fairuz And M. R. Ishal, "Prototype Expert System For Material Selection Of Polymeric Composite Automotive Dashboard," International Journal Of The Physical Sciences, Vol. Vol. 6(25), Pp. 5989-5995, 2011.