http://ejournal.polman-babel.ac.id/index.php/manutech/issue/feed Manutech : Jurnal Teknologi Manufaktur 2019-07-31T08:16:13+00:00 Dr. Parulian Silalahi, M.Pd parulian@polman-babel.ac.id Open Journal Systems <p><span style="font-family: helvetica; font-size: small;"><span style="font-family: helvetica; font-size: medium;">Manutech : Jurnal Teknologi Manufaktur</span></span></p> <p>&nbsp;<img src="/public/site/images/polmanbabelojs/cover_manutech.jpg"></p> <p>Manutech is a peer-reviewed journal for the publication of applied science research in the fields of engineering and manufacturing education, mechanical engineering, electronics, electricity, automation, and robotics.</p> <p>Manutech is published twice every year in June and December. Every published article has passed the review process. Manutech also publishes original articles and selected review articles specifically invited by the approval of Editor-in-Chief.</p> <p>Manutech is published by Pusat Penelitian dan Pengabdian kepada Masyarakat, Politeknik Manufaktur Negeri Bangka Belitung, Sungailiat - Bangka, Indonesia.</p> http://ejournal.polman-babel.ac.id/index.php/manutech/article/view/92 Pengaruh Kecepatan Putar Terhadap Hasil Coran pada Metode Pengecoran Sentrifugal dalam Pembuatan Produk Pisau Pakan Ternak dengan Material Ni-Hard1 2019-07-31T06:45:52+00:00 Roni Kusnowo roni@polman-bandung.ac.id Kus Hanaldi roni@polman-bandung.ac.id <p>Animal feed knife is a tool that serves to cut and chop animal feed consisting of grass as the main ingredient with additives such as bran, herbs, centrate, cassava, tofu pulp and others. Therefore, as a cutting tool must have the properties of friction resistance, impact resistance, and have good sharpness, so that the material chosen is Ni-Hard 1. The use of centrifugal casting method was chosen because it has the advantage of being able to make castings with relatively thin thickness this is due to the influence of the centrifugal force on the distribution of metal liquids throughout the cavity in the mold. Case study in this study is the use of centrifugal casting methods as an alternative to gravity casting methods to overcome defects of misruns. This research was conducted to investigate the effect of speed on the formation of castings products. The method that was carried out began with a literature study on centrifugal casting, and continued by determining the material, the temperature of the cast is in the range 1250ºC - 1300ºC, and the type of mold. The next step is to do work drawings, pattern making, mold making, casting processes, fettling processes, and analysis. With variations in speed of 200 rpm, 300 rpm and 400 rpm, it can be seen the optimal speed for making this product. The results of this study obtained optimal speed at a speed of 300 rpm to make good quality of animal feed knife products.</p> 2019-07-31T06:17:26+00:00 ##submission.copyrightStatement## http://ejournal.polman-babel.ac.id/index.php/manutech/article/view/90 Rancang Bangun Mesin Pengayak Pasir Untuk Meningkatkan Produktivitas Pengayakan Pasir Pada Pekerja Bangunan 2019-07-31T04:23:13+00:00 Angga Sateria angga@polman-babel.ac.id Eko Yudo angga@polman-babel.ac.id Zulfitriyanto Zulfitriyanto angga@polman-babel.ac.id Sugiyarto Sugiyarto angga@polman-babel.ac.id Rina Melati angga@polman-babel.ac.id Bimas E Saputra angga@polman-babel.ac.id Ikhya Naufal angga@polman-babel.ac.id <p>One of the materials used in the building process is sand particle. Sand with uniform size is generally obtained from manual sifting processes that require a lot of human power and long sieving time, so a sand sieving machine is needed to minimize the use of human power and sieving time. The design is focused on sifting sand manually into sieving using a machine. The design of the machine uses design software to create a picture of the arrangement and working drawings of the components of the sand sieving machine. Based on the results of the trials that have been carried out, the machine can sift 5 kg of sand for 1.02 minutes and for 10 kg of sand can be sifted for 1.30 minutes.</p> 2019-07-31T04:23:13+00:00 ##submission.copyrightStatement## http://ejournal.polman-babel.ac.id/index.php/manutech/article/view/93 Uji Mesin Crusher Brondolan Sawit dengan Mata Potong Circular Saw Standar 2019-07-31T06:28:32+00:00 Adhe Anggry adhe.anggry@yahoo.com Subkhan Subkhan adhe.anggry@yahoo.com <p>Palm brondolan are the outer fruit of the loose bunches and fall to the ground. Palm brondolan is used as a feed ingredient. Processing of palm brondolan for feed ingredients needs to be done by the process of damaging the material structure. This study aims to determine the quality of palm brondolan crusher using standard cutting eyes and determine the right shaft. In this study the crusher machine was designed using 13 circular cutting eyes to see the standard  4 x 1.75 mm, the number of teeth 40 pieces and the distance between cutting eyes 5 mm. This machine uses a source of driving power in the form of a 3 phase electric motor with 3 HP power and has a rotating speed of 1420 rpm and a rotation ratio of 1: 1 shaft. This study uses the experimental method, by comparing the shaft test with the quality of the palm blended crusher. The quality characteristics that are addressed are the smaller the better. The results of the study, obtained an effective engine capacity of 30 kg/hour. The quality of the crusher at 700 rpm shaft speed accelerated the size of coir length from 1 to 30 mm and the volume of shell and seed granules 8-27 mm3 while in shaft rotation 1420 rpm the size of 1-20 mm coir and the volume of grain and seeds 4-12 mm3 were obtained. From the results of the experiment proving that circular cutting eyes see the standard capable of destroying palm leaflets and shaft rotation affect the quality of the crusher. The 1420 rpm shaft rotation has a better crusher quality compared to 700 rpm shaft rotation.</p> 2019-07-31T06:28:32+00:00 ##submission.copyrightStatement## http://ejournal.polman-babel.ac.id/index.php/manutech/article/view/96 Lampu Sein Helm Sepeda Berbasis Voice Recognition 2019-07-31T06:55:19+00:00 Indra Dwisaputra indra@polman-babel.ac.id Parulian Silalahi indra@polman-babel.ac.id Bayu Cahyawan indra@polman-babel.ac.id Imam Akbar indra@polman-babel.ac.id <p>Bicycles are not equipped with the turn signal. For driving safety, a bicycle helmet with a turn signal is designed with voice rrecognition. It is using the Arduino Nano as a controller to control the ON and OFF of turn signal lights with voice commands. This device uses a Voice Recognition sensor and microphone that placed on a bicycle helmet. When the voice command is mentioned in the microphone, the Voice Recognition sensor will detect the command specified, the sensor will automatically read and send a signal to Arduino, then the turn signal will light up as instructed, the Arduino on the helmet will send an indicator signal via the Bluetooth Module. The device is able to detect sound with a percentage of 80%. The tool can work with a distance of &lt;2 meters with noise &lt;71 db.</p> 2019-07-31T06:55:19+00:00 ##submission.copyrightStatement## http://ejournal.polman-babel.ac.id/index.php/manutech/article/view/97 Optimasi Multirespon Purwarupa Electrical Discharge Machine (EDM) Menggunakan Metode Taguchi-Grey Relational Analysis 2019-07-31T07:03:36+00:00 Angga Sateria angga@polman-babel.ac.id Eko Yudo angga@polman-babel.ac.id Zulfitriyanto Zulfitriyanto angga@polman-babel.ac.id <p>EDM is one of the nonconventional machining processes when making workpieces with conventional machining processes is difficult. This process has been used effectively in machining hard, high-strength and high temperature materials such as high speed steel (HSS) materials. In this study, prototype of EDM machines was carried out with engine variables such as current (A), pulse on time (µs) and pulse off time (µs). The material used is high speed steel (HSS) material used in cutting tools such as turning tools and milling tools. Surface roughness and material removal rate are responses observed to determine the quality of material remaval. The quality characteristic of the surface roughness response is "smaller is better" and the quality characteristics of the material removal rate response is "larger is better. The purpose of this study is to determine the best process parameter level to achieve the required performance characteristics in the material removal process using prototype EDM machines using the gray relational analysis (GRA) method, three process parameters are selected such as current, pulse on time, and pulse off time. The taguchi 3 x 3 x 3 design is used as an experimental design.The best parameter level obtained is current 40 ampere, pulse on time 200 µs, pulse off time 20 µs.</p> 2019-07-31T07:03:36+00:00 ##submission.copyrightStatement## http://ejournal.polman-babel.ac.id/index.php/manutech/article/view/98 Optimasi Parameter Proses 3D Printing FDM Terhadap Akurasi Dimensi Menggunakan Filament Eflex 2019-07-31T08:16:13+00:00 Pristiansyah Pristiansyah pampersie30@gmail.com Hasdiansah Hasdiansah pampersie30@gmail.com Sugiyarto Sugiyarto pampersie30@gmail.com <p>Fused Deposition Modeling (FDM) is a 3D Printing technique used to print products using filaments as material. The printed product has ideal geometric characteristics if it has meticulous size and perfect shape. One type of material that can be processed using 3D Printing FDM is flexible material. Research in terms of dimensional accuracy has been carried out on PLA and ABS materials. While research using flexible materials is still rarely done. From these problems, we need a study to get the process parameter settings on a 3D Printer machine that is optimal in obtaining dimensional accuracy using flexible materials. The research was carried out using the Prusa model DIY (Do It Yourself) 3D machine with FDM technology. The material used is Eflex type flexible filament with a diameter of 1.75 mm. The process parameters used in this study are flowrate, layer thickness, temperature nozzle, speed printing, overlap, and fan speed. Cuboid test specimens measuring 20 mm × 20 mm × 20 mm. Process parameter optimization using the Taguchi L27 Orthogonal Array method for dimensional accuracy testing. Optimal process parameter values for obtaining X dimension accuracy are 110% flowrate, 0.10 mm layer thickness, 210 °C nozzle temperature, 40 mm/s print speed, 75% overlap, and 50% fan speed. Y dimension is 120% flowrate, layer thickness 0.20 mm, nozzle temperature 230 °C, print speed 30 mm/s, overlap 75%, and fan speed 100%. As well as the Z dimension is 120% flowrate, layer thickness 0.30 mm, nozzle temperature 210 °C, print speed 30 mm/s, overlap 50%, and fan speed 100%.</p> 2019-07-31T07:12:49+00:00 ##submission.copyrightStatement##